Philips IntelliVue MP5 Features
The Philips IntelliVue MP5 is a Compact patient monitor that can fit into a wide range of environments. The IntelliVue MP5 patient monitor has an 8.4 ” LCD touchscreen display. The display screen offers flexible screen configuration. Showing up to four different waveform measurements simultaneously. The Philips IntelliVue MP5 can measure 12 lead ECG. The MP5 can be connected to an IntelliVue MP20 through an MP90 monitor and can be used as a Multi-Measurement Module (MMS). The system has dedicated configurations for anesthesia, critical and cardiac, and neonatal care.
- Compact, rugged, lightweight monitor with built-in measurements
- ECG monitoring using any combination of three to 10 electrodes.
- 12-lead ECG monitoring with five electrodes using the EASI method or with 10 electrodes using the conventional method.
- Multi-lead arrhythmia and ST segment analysis at the bedside on all available leads.
- Respironics Mainstream or Sidestream CO2.
- FAST SpO2 for accurate performance even with low perfusion.
- Invasive Pressure and Temperature Measurement.
- Choice of either auscultatory or intra-arterial measurements as a measurement reference for Non-Invasive Blood Pressure.
Philips IntelliVue MP5 Specifications
Dimensions
- Height: 9.76″ (24.8 cm)
- Width: 10.2″ (25.9 cm)
- Depth: 7.32″ (18.6 cm)
- Weight: 8.8 lbs (4 kg)
Power
- Power Consumption: < 40W average; < 65W Peak
- Line Voltage: 100 to 240 V ~
- Current: 1.3 to 0.7A
- Frequency: 50/60 Hz
Display
- Type: SVGA
- Size: 8.4″ (21.3 cm)
- Resolution: 800 x 600
- Refresh Rate: 60 Hz
Battery
- Type: Lithium-Ion
- Capacity: 6000 mAh
- Voltage: 10.8 V
- Weight: 480g (Per battery)
- Charge Time: 4 hours (When off); 5 hours or more when on
- Operating Time: 4 Hours (Basic monitoring configuration); 3 hours (Extended monitoring configuration)
Operating Environmental Specifications
- Temperature: 32 to 104°F (0 to 40°C)
- Humidity: 15 to 95% non condensing
- Altitude: 10,000 ft (-500 to 3000 m)
Storage Environmental Specifications
- Temperature: -4 to 140°F (-20 to 60°C)
- Humidity: 5 to 90% non condensing
- Altitude: 15,000 ft (-500 to 4600 m)
Sweep Speeds
- 6.25, 12.5, and 50 mm/s with +/- 5% accuracy
CO2
- Range: 0 to 150 mmHg (0 to 20.0 kPa)
- Accuracy: after 2 minutes warmup: For values between 0 and 40 mmHg:±2.0 mmHg (±0.29 kPa) For values from 41 to 70 mmHg: ±5% of reading For values from 71 to 100 mmHg: ±8% of reading The specifications are valid for standard gas mixtures, balance air, fully hydrated at 35°C, Pabs = 760 mmHg, flow rate = 2 l/min
- Resolution: Numeric: 1.0 mmHg (0.1 kPa); Wave: 0.1 mmHg (0.01 kPa)
- Stability: Short-term drift: ±0.8 mmHg over four hours; Long-term drift: Accuracy specification will be maintained over a 120 hour period
awRR
- Range: 2 to 150 rpm
- Accuracy: ±1 rpm
Warm-up Time
- 2 minutes with CO2 transducer attached for full accuracy specification
Response Time
- Less than 60 ms
Temperature
Temp
- Range: –1 to 45 °C (30 to 113 °F)
- Resolution: 0.1 °C (0.2 °F)
- Accuracy: ±0.1 °C (±0.2 °F)
Average Time Constant
- Less than 10 seconds
Alarms
- Range: –1 to 45 °C (30 to 113 °F)
- Adjustment: -1 to 35 °C (30 to 95 °F): 0.5 °C (1.0 °F) steps 35 to 45 °C (95 to 113 °F): 0.1 °C (0.2 °F) steps
Invasive Pressure Performance
Measurement Range
- –40 to 360 mmHg
Pulse Rate
- Range: 25 to 350 bpm
- Accuracy: ±1% Full Range
- Resolution: 1 bpm
Input Sensitivity
- Sensitivity:5µV/V/mmHg (37.5µV/ V/kPa)
- Adjustment range:±10%
Transducer
- Load Impedance:200 to 2000 O (resistive)
- Output Impedance:=3000 O (resistive)
Frequency Response
- dc to 12.5 Hz or 40 Hz
Zero Adjustment
- Range: ±200 mmHg (±26 kPa)
- Accuracy: ±1 mmHg (±0.1 kPa)
- Drift: Less than 0.1mmHg/°C (0.013 kPa/ °C)
NBP Performance Specifications
Measurement Ranges
- Systolic: Adult: 30 to 270 mmHg (4 to 36 kPa); Pedi: 30 to 180 mmHg (4 to 24 kPa); Neo: 30 to 130 mmHg (4 to 17 kPa)
- Diastolic: Adult: 10 to 245 mmHg (1.5 to 32 kPa); Pedi: 10 to 150 mmHg (1.5 to 20 kPa); Neo: 10 to 100 mmHg (1.5 to 13 kPa)
- Mean: Adult: 20 to 255 mmHg (2.5 to 34 kPa); Pedi: 20 to 160 mmHg (2.5 to 21 kPa); Neo: 20 to 120 mmHg (2.5 to 16 kPa)
- Pulse Rage: Adult:40 to 300; Pedi: 40 to 300; Neo: 40 to 300
Accuracy
- Max. Std. Deviation: 8 mmHg (1.1 kPa)
- Max. Mean Error: ±5 mmHg (±0.7 kPa)
Pulse Rate Measurement Accuracy
- 40 to 100 bpm: ± 5 bpm
- 101 to 200 bpm: ± 5% of reading
- 201 to 300 bpm: ± 10% of reading (average over NBP measurement cycle)
Heart Rate Range
- 40 to 300 bpm
Measurement Time
- Typical at HR > 60bpm
- Auto/manual: 30 seconds (adult) 25 seconds (neonatal) Stat: 20 seconds
- Maximum time: 180 seconds (adult/pediatric) 90 seconds (neonates)
Cuff Inflation Time
- Typical for normal adult cuff: Less than 10 seconds
- Typical for neonatal cuff: Less than 2 seconds
SpO2 Performance Specifications
Pulse
- Range: 30 to 300 bpm
- Accuracy: ±2% or 1 bpm, whichever is greater
- Resolution: 1 bpm
Sensors
- Wavelength range: 500 to 1000 nm
- Emitted Light Energy: = 15mW Information about the wavelength range can be especially useful to clinicians (for instance, when photodynamic therapy is performed)
Pulse Oximeter Calibration Range
- 70 – 100%
ECG Arrhythmia and ST Performance
Cardiotach
- Range: Adult/pedi: 15 to 300 bpm; Neo range: 15 to 350 bpm
- Accuracy: ±1% of range
- Resolution: 1 bpm
- Sensitivity: =200 µVpeak
PVC Rate
- Range: 0 to 300 bpm
- Resolution: 1 bpm
ST Numeric
- Range: -20 to +20 mm
- Accuracy: ±0.5 mm or 15%, whichever is greater
- Resolution: 0.1 mm
Sinus and SV Rhythm Ranges
- Brady: Adult: 15 to 60 bpm; Pedi: 15 to 80 bpm; Neo: 15 to 90 bpm
- Normal: Adult:60 to 100 bpm; Pedi: 80 to 160 bpm; Neo: 90 to 180 bpm
- Tachy: Adult: > 100 bpm; Pedi: >160 bpm; Neo: >180 bpm
Bandwidth
- Diagnostic Mode: Adult/neo/pedi: 0.05 to 150Hz
- Extended Monitoring Mode: Neo/pedi: 0.5 to 150Hz
- Monitoring Mode: Adult: 0.5 to 40Hz; Neo/pedi: 0.5 to 55Hz
- Filter mode: Adult/neo/pedi: 0.5 to 20H
HR
- Range: 15 to 300 bpm maximum delay: 10 seconds according to AAMI EC 13- 1992 standard
Refurbished Philips Intellivue MP5 Patient Monitor System
Soma Tech Intl offers Refurbished Philips IntelliVue MP5 up to 50% below OEM prices with the same service and warranty as new. The Philips Patient Monitor is not only technically refurbished but also cosmetically refurbished to make it work and look new. When the refurbishing process starts the Philips Patient Monitor system is carefully inspected and tested by our own in-house biomedical engineers who are highly skilled and certified to work on the Philips Patient Monitor. If necessary, parts are replaced to make sure that all aspects of the monitor are functioning properly. Once everything is in working order, the unit is calibrated back to the original engineering manufacturer’s specifications. This ensures that the unit is working the same way that it originally left the manufacturer. After the Philips IntelliVue MP5 Patient Monitor system is working like new it undergoes a special cosmetic restoration process. The Monitor is cleaned, minor scratches and dents are repaired, it’s painted, and new decals are replaced if necessary. After this strenuous refurbishing process, the Patient Monitor functions and looks like new. Soma Tech is ISO 13485 certified and ensures that the best quality is given to all capital medical equipment that they sell. Before the Patient Monitor is labeled patient-ready and packed up for shipment, it goes through one last quality control test that makes sure all aspects are again working as they should. If you are looking to buy refurbished Philips IntelliVue MP5 Monitor contact soma at [email protected] or call us at 1-800-GET-SOMA.
Soma Tech Intl is also actively looking to purchase an IntelliVue MP5 Monitor. If you or your facility is looking to sell your Philips InlelliVue, be sure to contact Soma Tech Intl. Soma has a dedicated and experienced purchasing department that helps you through the entire process. Selling your used or pre-owned Philips Patient Monitor to Soma Tech takes out the middle man in the equation. This also ensures that your medical facility gets top dollar for your equipment. Soma Tech is 100% HIPPA compliant and makes sure that your equipment gets to our facility in the same condition that it left yours. Soma Tech also gives the option for trade-in credit on your medical equipment. If you or your facility is looking to regain floor space for new equipment, or looking to upgrade current equipment, contact Soma Tech’s purchasing department at [email protected] or send us a message on our Sell to Soma website.
