Reliance 444 Series Washer

Cycle Discription

ADVISORY NOTE: Reliance 444 Single-Chamber Washer/Disinfectors are intended only to perform an initial step in the reprocessing of soiled, reusable medical devices. STERIS does not recommend, represent, or warrant the Reli-ance Washer/Disinfector be used for the terminal disinfection or sterilization of any regulated medical device. If medical devices will be contacting blood or com-promised tissues, such devices must be terminally reprocessed in accordance with current good hospital practices before each use in human patients. On initial daily start-up, setting the POWER-OFF/STANDBY switch to POWER prepares the washer/disinfector for cycle operation. Once the treatment cycle is selected, the washer/disinfector automatically processes the load through the following standard (additional phases are included in certain treatment cycles, depending on unit configuration) phases:

• Pre-Wash: Water (cold or hot) enters the sump from the building supply. Once the sump fills, pre-wash water is recirculated and sprayed over the load for the selected time interval (15 seconds to 15 minutes [2 to 15 minutes for Instrument, Anesthesia/Respiratory Goods and Gentle Cycles]). On completion of the phase, water is sent to the drain.
• Wash: Hot tap water enters the sump from the building supply, where a selected amount of detergent is added automatically. The detergent solution is heated and maintained at a temperature ranging between 140 and 180°F (60 and 82°C). Once the set temperature is reached, the solution is recirculated and sprayed over the load for the selected time interval (2 to 15 minutes). On completion of the phase, the solution is sent to the drain.
• Rinse: Hot tap water enters the sump from the building supply. Rinse water may be heated and maintained at a temperature ranging between 110 and 180°F (43 and 82°C). Once sump fills, rinse water is recirculated and sprayed over the load for the selected time interval (15 seconds to 15 minutes). On completion of the phase, water is sent to the drain.
• Thermal Rinse: Water (hot or optional purified) enters the sump from the building supply. Rinse water is heated and maintained at a temperature ranging between 180 and 203°F (82 and 95°C). Once the set temperature is reached, the rinse water is recirculated and sprayed over the load for the selected time interval (1 to 10 minutes). On completion of the phase, water is sent to the drain.

On completion of daily usage, washer/disinfector can be placed in a standby mode by setting POWER-OFF/STANDBY switch to the OFF/STANDBY position. Once the switch is set, there is a one-minute delay before the power door(s) automatically locks, and sump drains for two minutes.

Refurbished Reliance 444 Series Washer

Soma Tech Intl offers Reliance 444 Series Washer up to 50% below OEM prices with the same service and warranty as new. The Reliance 444 Series Washer is not only technically refurbished but also cosmetically refurbished to make it work and look like new. When the refurbishing process starts on the Reliance 444 Series, it is carefully inspected and tested by our own in-house biomedical engineers that are highly skilled and certified to work on washers and disinfectors. If necessary, parts are replaced to make sure that all aspects of the Reliance 444 Series are functioning properly. Once everything is in working order, the unit is calibrated back to the original engineering manufacturer specifications. This ensures that the unit is working the same way that it originally left the manufacturer. After the Reliance 444 Series is working like new it undergoes a special cosmetic restoration process. The Reliance 444 Series is cleaned, minor scratches and dents are repaired, it's painted, and new decals are replaced if necessary. After this strenuous refurbishing process, the unit functions and looks like new. Soma Tech Intl is ISO 13485 certified and ensures that the best quality is given to all capital medical equipment that they sell. Before the Reliance 444 Series is labeled patient-ready and packed up for shipment, it goes through one last quality control test that makes sure all aspects are again working as they should. If you are looking to buy refurbished Reliance 444 Series contact soma at [email protected] or call us at 1-800-GET-SOMA.

Soma Tech Intl is also actively looking to purchase a Reliance 444 Series If you or your facility is looking to sell your Reliance 444 Series /a>, be sure to contact Soma Tech Intl. Soma has a dedicated and experienced purchasing department that helps you through the entire process. Selling your used or pre-owned Reliance 444 Series to Soma Tech Intl takes out the middle man in the equation. This also ensures that your medical facility gets top dollar for your equipment. Soma is 100% HIPPA compliant and makes sure that your equipment gets to our facility in the same condition that it left yours. Soma Tech Intl also gives the option for trade-in credit on your medical equipment. If you or your facility is looking to regain space for new equipment, or if you are looking to upgrade your current equipment, contact Soma Techn Intl's purchasing department at [email protected] or send us a message on our Sell to Soma website.