Steris Amsco 3052

Steris Amsco 3052 Specifications

Dimensions

• Height: 80″ (203.2 cm)
• Width: 42″ (106.7 cm)
• Length: 31″ (78.7 cm)
• Load Height: 31″ (78.7 cm)

Utility Requirements

• Hot, Cold, and Pure Water; Steam; Condensate Return: 1/2 NPT
• Air: 1/8 NPT
• Ventilation: 3″ (7.6 cm) O.D.
• Drain: Recommended minimum 4″ (10.2 cm) floor drain. An 8 x 8″ (20.4 x 20.4 cm) floor sink is also recommended.

Safety Features

• Vertical chamber doors are equipped with an obstruction sensor to detect any door obstruction. If an obstruction is present the door automatically opens.
• The washer/disinfector is equipped with a safety lockout feature so a cycle cannot start unless the door is fully closed.
• A door interlock feature is provided to prevent cross-contamination. The door interlock feature allows only one door to be opened at a time whenever power is on.
• Safety spot pushbuttons, one on the load and one on the unload side, automatically stop all unit operations when pressed.
• Building electrical supply disconnect switch must be used to shut off power to the unit before servicing.

Wash Chamber Construction

• 16-gauge, #3-4 L stainless steel, argon-welded and polished.
• The chamber is of sanitary-type design (horizontal fixed surfaces are sloped, overlapping metal sheets) for complete drainability and to reduce hard-to-clean locations.
• Single-walled, insulated construction of the chamber exterior reduces heat loss and noise level in the work area.
• Rotary spray assemblies are positioned at the top and the bottom of the chamber, each measuring 24-3/8″ (62 cm) long to reach all load surfaces, Spray assemblies are easily removable without tools to aid in cleaning and maintenance.
• 3-W LED light mounted within an explosion/vapor-proof enclosure, illuminates chamber interior.

System Drying

• The drying system is manifold and circulates HEPA-filtered air through piping, accessories, and chamber for 1 to 60 minutes at low temperatures of 108°F (82°C) or 1 to 30 minutes at a high temperature of 240°F (115°C).
• The system includes a cold water condenser.
• The system includes a 3hp (2.2 kW), blower and three electric heaters totaling 11.4kW.
• The system heats and maintains the chamber to 180-240°F (82-115°C). No additional ductwork is required.

Pure Water Rinse Supply

• Washer/disinfector is equipped with a Pure Water Stainless-Steel Supply Valve.
• Pure water from the facility is sprayed over the load under pump pressure for 15 seconds (adjustable from 15 seconds to 15 minutes.)
• Up to four Pure Water Rinse treatments can be selected per cycle with recirculated water.
• Pure water can be used for thermal disinfection stage and is heated to 194°F (90°C) using either steam or electric heaters.

Drain Discharge Cool Down

• This feature assures water drained at the end of each phase, from the chamber sump to the building drain system, does not exceed 140°F (60°C).
• If the water temperature in the sump is higher than 140°F (60°C), cold water is automatically added to reduce the temperature of the water discharged into the building drain system.

Sump

• Constructed of #304 L Stainless steel with 9.5 gal (36 L) capacity.
• The removable stainless-steel filter in the chamber sump prevents debris from entering the pump and piping system.
• The heating coil at the bottom of the wash chamber (sump) raises and maintains water temperature up to 180°F (82°C) during the Wash phase and up to 194°F (90°C) during the Thermal Rise phase.

Chemical Injection Pumps

• Pumps are optimized to use Prolystica Ultra Concentrate chemicals. Each ultra-concentrated product is 10 times more concentrated than an equivalent traditional product; so 10 times less chemical is injected per cycle.
• The washer/disinfector comes with one enzyme and one detergent injection peristaltic pump which automatically add a selected quantity of chemical from 1/40 to 2oz/gal (0.2 to 16 mL/L)
• One injection peristaltic pump is dedicated to automatically adding a selected quantity of lubricant during the Thermal Rise phase.
• Pumps are positioned near chemical containers.

Microprocessor Control System

• Equipped with a 5.7″ (14.5 cm) touch-screen customer interface that is mounted at eye level beside the chamber door on both sides of the unit.
• Locking program cycle parameters with an access code.
• Service mode for preventive maintenance testing and facilitate troubleshooting.
• Built-in service diagnostic program to permit system calibration and verification of component operations.
• Security lock-out feature that enables programs and temperatures to be locked and unchangeable without the proper access code.
• Equipped with an audible warning system.