Medtronic NIM-Response 2.0

24-Hour Quotes

Pricing up to 50% below the cost of new,
with service and warranty included.
Download Specifications

Medtronic NIM-Response 2.0 Features

The Medtronic NIM-Response 2.0 is an Electromyography (EMG) Monitor. The NIM-Response 2.0 is a four-channel EMG Monitor that can be used for nerve monitoring during surgeries such as ENT and general surgery. The NIM-Response 2.0 can record Electromyographic (EMC) activity and can help the surgeon locate nerves that may be in the area where surgery is needed. The NIM system can provide audible and visual warnings if there are changes to the patient’s nervous system. The monitoring system offers various ports to connect a USB or mass storage device the collect the recordings. The Medtronic Electromyographic Monitor has a touchscreen that can display up to four different waveforms and peak-to-peak amplitude. Medtronic offers a variety of different Electromyographic (EMG) devices, another device would be the Medtronic NIM-Response 3.0.

  • 4-channel EMG monitor that is individually and simultaneously selectable.
  • High contrast digital color touch display.
  • Increased sensitivity with reduced interference.
  • Printable log of patient’s EMG activity.
  • More sensitive to lower-level EMG activity with the improved signal-to-noise ratio.
  • Quick setup.

Medtronic NIM-Response 2.0 Specifications

Dimensions

  • Height: 10.6” (27 cm)
  • Width: 12.2” (31 cm)
  • Depth: 14.5” (37 cm)
  • Weight: 18.7 lbs (8.5 kg)

Display

  • Type: High contrast, digital, graphic Color, visible in complete darkness.
  • Resolution: Display 600H x 800W pixels, Touch Panel 256H x 256W
  • Dedicated Function Event Touch Screen Controls: For Amplitude, Time Display and Capture.
  • Vertical Display: 50, 200, 500, and 2,000 µV display modes.
  • Event Capture: Enable/disable the capture mode indicator on the touch screen.
  • Time Scale: 50ms or 10s display modes.

Amplifier

  • Channels – 1 to 4: Individually and simultaneously selectable.
  • Input Sensitivities: 5 – 10,000 µV peak-to-peak AC-coupled
  • Sensitivity Selection: Automatically zeroed
  • Bandpass: 100 Hz – 2 kHz EMG Display; 200 Hz – 3.2 kHz Audio EMG Speaker
  • Input Noise: 5-11 µV p-p < 3 µV RMS @ DC – 4 Hz, inputs shorted
  • Input Impedance: > 200 K Ohm ± 10%
  • DC Offset Rejection: ± 0.540 V DC Rejection
  • Common Mode Rejection: >90 dB @ 60 Hz, balanced inputs, >70 dB @ 60 Hz, 1 K
  • Channel Enable/Disable Controls: Dedicated function touchpads for independent channel enable/disable.
  • Event Threshold Control and Display: Adjustable Graduated Touch Bar with Voltage threshold displayed.
  • Patient Isolation: 1,000 Vrms 60 Hz < 100 µA

Impedance Measurement

  • Control: Automatic CHECK ELECTRODE feature
  • Measuring Signal: 20 µA peak-to-peak, 60 Hz Square wave
  • Measurement Range: 0-200 K Ohm ± 10%

Artifact Detection and Rejection

  • Stimulus Artifact: Synchronized and adjustable muting.
  • Electrocautery Interference: Automatic detection, muting, and warning.
  • Electrode Lead Off: Automatic detection, muting, and warning.

Stimulator

  • Stimulus Type Constant: Constant Current
  • Stimulus Range: 0-30 mA, maximum 120 V compliance
  • Stimulus Control: Digitally controlled, range–dependent adjustment increments of .01, .05, 1.0, and 5.0 mA.
  • Stimulus Output Accuracy: ± .02 mA (or ± 5% of reading at 1K load) over Stimulus Range.
  • Stimulus Adjustment: Graduated Touch Screen Control with a display of command current and delivered current.
  • Stimulus Measurement Accuracy: ± .02 mA (or ± 5% of reading at 1K load) over Stimulus Range.
  • Internal Fuse: 32 mA Type F, 250V 5 x 20mm (It must be Xomed # 8250615, other similar fuses may not give the same degree of protection.

Stimulus Characteristics

  • Waveform: Monophasic, square pulse
  • Duration: Software selectable, 50, 100, 150, 200, or 250 µs
  • Rise Time: Less than 20 µs
  • Rate: Software selectable, 1, 4, 7, or 10 Hz
  • Stimulus Probe: Monopolar (standard) or bipolar

I / O – Printer Output / Disk Drive Output

  • Printer Interface: Hewlett-Packard: Model: DeskJet 5650 printer.
  • Connection: Centronics Parallel 36-pin female or USB (2)

Video Output

  • Interface: VGA Compatible, 800 x 600 resolution
  • Connection: 15-pin HD

Electrical

  • Input Voltage: 100V, 120V, 220V, and 230-240V ± 10%
  • Frequency: 50/60 Hz
  • Power Consumption: 47 W Nominal, <70 W Peak
  • Auxiliary AC output: 250 VA Max.
  • Line Isolation: 4000 V Peak-to-Peak 60 Hz dielectric withstand from Line
  • Internal Fuse: 5 x 20mm, 4Amp, 250V, Quick-acting, Low breaking capacity, Xomed Part # 11270037. Order 8250614 Fuse Kit for replacements.