Physio-Control Lifepak 9

Physio-Control Lifepak 9 Specifications

Dimensions

• Height: 35.2 cm (13.9 in)<//li>
• Width: 29.7 cm (11.7 in)
• Depth: 31cm (12.2 in)
• Weight: 12.7 kg ( 28 lbs)

General specifications

• Power Cord Length: 3m (10 Ft)
• Standard Paddle Electrode area: 82 square cm
• AC Input Option: 120 or 240 Vac nominal line voltage without adjustment. 50 or 60Hz, with adjustment in the SET UP menu.
• Battery type: Sealed lead-acid, 16 Vdc nominal, 3 Amp-hour
• low battery indicator: Advises operator to connect AC power.
• Battery Charge Indicator: Illuminates when the battery is charging.
• Battery Charge Time: 24 hours to full capacity. <?li>
• Service Indicator: Indicates self-diagnostic routines have detected improper operation requiring service attention.
• Power Consumption: 160 Watts maximum while monitoring with recorder ON and defibrillator charging.

ECG Monitor

• ECG Lead Selections: Std, Paddles, I, II, III
• Input: Isolated ECG via QUIK-LOOK® defibrillator paddles, FAST-PATCH® disposable defibrillation/ ECG electrodes, or 3-lead patient cable.
• Patient Cable Length: 4.0m (13 ft) total length; 3.1m cable (10 ft) with 0.9m leads (3 ft)
• Common Mode Rejection: 100dB minimum with respect to chassis ground and 65dB minimum with respect to isolated ground, when measured at 60Hz. Common mode range for patient cable input = 10 Volts peak with respect to isolated ground.
• Monitor Display Size:102mm (4 in) wide x 76mm (3 in) tall, non-fade
• Sweep Speed: 25mm/second
• Frequency Response: Non-diagnostic
• ECG Leads:1.0 to 40Hz (-3dB) <?li>
• Paddles: 2.2 to 20Hz (-3dB)
• ECG Size: Adjusts amplitude of ECG trace on monitor and strip chart recorder. <?li>
• Heart Rate Meter: 3-digit readout displays rates from 20 to 300 bpm. Heart rates outside this range do not yield valid systole tones or heart rate displays. Heart Rate Alarm: User-selectable alarm limits. Three high/low settings (150/40, 120/60, 160/90). Other limit options are available via the SET UP menu.
• 1 mV Cal: A momentary pushbutton switch on the rear panel simulates a 1 mV signal pulse to the ECG input.
• ECG Output:1 Volt/mV

Defibrillator

• Defibrillator Waveform: 5-millisecond monophasic pulse (Edmark)
• Energy Select:
  • External Paddles: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 50, 100, 200, 300, 360 Joules
  • Internal Paddles: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 50 Joules
• Charge Controls: Independent momentary push-button controls on the front panel and APEX paddle.
• Paddle Cord Length:3m (10 ft)
• Charge Indicators: Flashing lamps on the paddle and front panel pushbutton along with increasing stored energy display indicate a charge in progress. Upon full charge, the energy available is displayed on the monitor and charge completed tone sounds.
• Charge Time: Charge to 360 Joules in less than 10 seconds with a fully charged battery.
• SYNC: Synchronizes defibrillator pulse to patientgenerated QRS complex.
• SYNC Indicator: The inverted triangle marker on the displayed ECG waveform identifies the synchronizer trigger point with respect to the patient’s QRS complex.

Thermal Array Recorder

• Paper Size: 50mm wide x 30m (100 ft) <?li>
• Paper Speed: 25mm/second <?li>
• Delay: ECG prints 8 seconds after first appearing on the monitor.
• Frequency Response: Non-diagnostic. Diagnostic available via SET UP menu.
• ECG Leads (non-diagnostic): 1.0 to 40Hz (-3dB)
• ECG Leads (diagnostic): 0.05 to 100Hz (-3dB)
• Paddles: 2.2 to 20Hz (-3dB)
• Annotation: Time, date, ECG lead, ECG gain, heart rate, defibrillation parameters, test load discharges
• CODE SUMMARY Critical Event Record: Digitally stored record of ECG and device parameters

Environmental

• Atmospheric Pressure: 797mmHg to 500mmHg (-570 to 11000 ft)
• Relative Humidity: <?li>
  • 0 to 95% (non-condensing) at 0 to 34°C
  • 0 to 80% (non-condensing) at 35 to 45°C
• Temperature Range: 0 to 45°C operating -30 to 65°C storage
• All specifications at 20°C unless otherwise stated.