GE Dinamap ProCare 300
24-Hour QuotesPricing up to 50% below the cost of new,
with service and warranty included. Download Specifications
GE Dinamap ProCare 300 Features
The GE Dinamap ProCare 300 is an easy-to-use vital signs monitor. The GE Dinamap Procare 300 provides non-invasive blood pressure, diastolic blood pressure, pulse rate, SpO2, and temperature. The GE patient monitor has an intuitive menu and can hold up to 24 hours of trending data. The small size of the GE Dinamap ProCare 300 makes it versatile and easy to move from department to department, including; Emergency rooms, surgery centers, endoscopy, recovery, and labor and delivery. GE offers a few different non-invasive blood pressure monitors the GE Dinamap Procare 400.
- NIBP, SpO2 & Recorder
- Comprehensive — One monitor for the entire range of patient populations – Neonatal, Pediatric, and adult
- Versatile – Used in ER, Outpatient Surgery, Endoscopy, GI Lab, Special Procedures, Recovery/PACU,
Telemetry, Med-Surg, and Labor & Delivery - Easy To Use – Push Button Interface
- DINAMAP NIBP Technology — Available in GE Solar and Dash monitors
- Six Sigma Quality & Reliability – Built-In Quality Means Accurate Readings
- Connectivity Options
GE Dinamap Procare 300 Specifications
Medical
- Dimensions (without temperature): 9.7 (H) × 8.6 (W) × 5.3 (D) inches (24.7 × 2.9 × 13.5 cm)
- Dimensions (with temperature): 9.7 (H) × 10.0 (W) × 5.3 (D) inches (24.7 × 25.4 × 13.5 cm)
- Mountings: Self-supporting on rubber feet
- Portability: Carried by handle
Monitor
- Protection against electrical shock: Internally powered or Class II when powered from a specified external power supply.
- DC input voltage: 12 VDC, supplied from a source conforming to IEC 601-1
- Fuses: The Monitor contains four fuses. The fuses are auto-resettable and mounted within the Monitor. The fuses protect the low-voltage DC input, the battery, the remote alarm output, and the +5 V output on the host port connector.
- Battery: 6 volts, 3.3 amp-hours protected by internal auto-resetting fuse and thermal protection.
- Minimum operation time: 2 hrs (5 min cycle with an adult cuff at 25°C, SpO2 active at 60 bpm, Temp in monitor mode, a printout of current values every 5 minutes) from a full charge.
- Time for full recharge: Approx. 5 hrs from full discharge when the Monitor is switched off and approx. 8 hrs when the Monitor has switched on
Blood Pressure
- Cuff pressure range: 10 to 290 mmHg (adult/ped); 10 to 140 mmHg (neonate)
- Blood pressure accuracy: meets or exceeds ANSI/AAMI standard SP-10 (mean error =55mmHg, standard deviation =8mmHg
- Maximum determination time: 120 seconds (adult/ped) and 85 seconds (neonates)
- Overpressure cutoff: 330 mmHg (adult/ped) and 165 mmHg (neonate)
- Pulse rate range: 30 to 200 beats/min (adult/ped) and 30 to 220 beats/min (neonate)
- Pulse rate accuracy: ±3.5%
- Systolic limits (mmHg): 200 high and 80 low
- Diastolic limits (mmHg): 120 high and 30 low
- Inflation pressure: 160 mmHg (adult/ped) and 110 mmHg (neonate)
- Cycle button: 15
Sp02
- SpO2 measurement range: 10 to 100%
- Pulse rate measurement range: 20 to 250 beats/min
- Accuracy and motion tolerance: adult without motion – 70 to 100% ±2 digits; neonate without motion – 70 to 100% ±3 digits; adult and neonate with motion – 70 to 100% ±3 digits
- Low perfusion: 70 to 100% ±2 digits, 0 to 69% unspecified
- Pulse rate without motion: 20 to 250 beats/min ±3 digits
- Pulse rate with motion: normal physiologic range 55 to 125 beats/min ±5 digits
- Pulse rate low perfusion: 20 to 250 beats/min ±3 digits
Pulse rate
- High: 150
- Low: 50
Temperature
- Predictive mode range: 41.1° C and 106.0°F maximum and 35.6°C and 96.0°F minimum
- Monitor mode range: 41.1°C and 106.0°F maximum and 26.7°C and 80.0°F minimum
- Monitor mode accuracy: ±0.1°C; 0.2°F (when tested in a calibrated liquid bath)
- Determination time: approximately 10 seconds, typical
Refurbished The GE Dinamap ProCare 300 Monitor
Soma Tech Intl offers the GE Dinamap ProCare 300 Patient Monitor up to 50% below OEM prices with the same service and warranty as new. The GE Monitor is not only technically refurbished but also cosmetically refurbished to make it work and look new. When the refurbishing process starts on the patient monitors, it is carefully inspected and tested by our own in-house biomedical engineers who are highly skilled and certified to work on patient monitors. If necessary, parts are replaced to make sure that all aspects of the monitor are to the original engineering manufacturer’s specifications. This ensures that the unit is working the same way that it originally left the manufacturer. After the ProCare 300 monitor is working like new it undergoes a special cosmetic restoration process. The monitor is cleaned, minor scratches and dents are repaired, it’s painted, and new decals are replaced if necessary. After this strenuous refurbishing process, the unit functions and looks like new. Soma Tech Intl is ISO 13485 certified and ensures that the best quality is given to all capital medical equipment that they sell. Before the GE ProCare 300 monitor is labeled patient-ready and packed up for shipment, it goes through one last quality control test that makes sure all aspects are again working as they should. If you are looking to buy a refurbished stretcher contact soma at [email protected] or call us at 1-800-GET-SOMA.
Soma Tech Intl is actively looking to purchase GE patient monitors, If you or your facility is looking to sell your vital signs monitors, be sure to contact Soma Tech Intl. Soma has a dedicated and experienced purchasing department that helps you through the entire process. Selling your used or pre-owned GE monitors takes out the middleman in the equation. This also ensures that your medical facility gets top dollar for your equipment. Soma is 100% HIPPA compliant and makes sure that your equipment gets to our facility in the same condition that it left yours. Soma Tech Intl also gives the option for trade-in credit on your medical equipment. If you or your facility is looking to regain space for new equipment, or if you are looking to upgrade your current equipment, contact Soma Techn Intl’s purchasing department at [email protected] or send us a message on our Sell to Soma website.