Steris Reliance Synergy

Cycle Despription

On initial daily start-up, setting the POWER-OFF/STANDBY switch to POWER prepares the washer/disinfector for cycle operation.

Once the treatment cycle is selected, the washer/disinfector automatically processes the load through the following standard phases (additional phases are included in certain treatment cycles depending on unit configuration):

• Pre-Wash. Cold water enters the sump from the building supply. Once the sump fills, pre-wash water is recirculated and sprayed over the load for two minutes (factory-setting). On completion of the phase, water is sent to the drain. Recirculation time is adjustable from 15 seconds to 15 minutes.

• Pulsed Enzyme. Hot tap water enters sump from the building supply, where a selected amount of enzyme detergent is added automatically. The load is sprayed with an enzyme solution for 4.0 seconds, then allowed to soak on instruments for 26 seconds. Spray/soak pattern is repeated for the selected time interval (4.0 to 15 minutes). On completion of the phase, the solution is sent to drain, and the load is rinsed with hot water.

• Wash. Hot tap water enters the sump from the building supply, where a selected amount of detergent is added automatically. The detergent solution is heated and maintained at a temperature ranging from 140 to 180°F (60 to 82°C); the factory setting is 150°F (65°C). Once set temperature is reached, a solution is recirculated and sprayed over the load for the selected time interval (2.0 to 15 minutes). On completion of the phase, the solution is sent to the drain.
• Neutralizer. Hot tap water enters the sump from the building supply, where a selected amount of neutralizing detergent is added automatically. The detergent solution is heated and maintained at a temperature ranging from 140 to 180°F (60 to 82°C); the factory setting is 150°F (65°C). Once set temperature is reached, the solution is recirculated and sprayed over the load for the selected time interval (2.0 to 15 minutes). On completion of the phase, the solution is sent to the drain.
• Rinse. Hot tap water enters the sump from the building supply. Water may be heated and maintained at a temperature ranging from 110 to 180°F (43 to 82°C) for 15 seconds (factory-setting). Once the sump fills, rinse water is recirculated and sprayed over the load for the selected time interval (15 seconds to 15 minutes). On completion of the phase, water is sent to the drain.
• Thermal Rinse. Pure water, or hot tap water, enters the sump from the building supply. Pure water rinse is recirculated, heated and maintained at a temperature ranging from 180 to 203°F (82 to 95°C). Once the set temperature is reached, rinse water is recirculated and sprayed over the load for the selected time interval (1.0 to 10 minutes).
  In North American washing applications (60-Hz units), a lubricant is automatically injected during the Thermal Rinse at a concentration of 1/8 to 2.0 oz/gal (1.0 to 16 mL/L). On completion of the phase, water is sent to the drain.
• HEPA-Filtered Drying. Hot air is recirculated over the load for 6.0 to 60 minutes at low temperature (180°F [82°C]), or 6.0 to 30 minutes at a high temperature (240°F [116°C]). During the Drying phase, a small quantity of air (approximately 50 scfm) is exhausted through the building vent system, or through the condenser (non-vented system option) to reduce humidity. This exhausted air is replaced by HEPA-filtered fresh air.
  
  The drying efficiency is enhanced by high convection of hot air through diffusers in the chamber and piping in the manifold racks.

On completion of daily usage, the washer can be placed in a STANDBY Mode by setting Power-Off/Standby switch to OFF/ STANDBY position.

Once the switch is set, there is a one-minute delay before the power doors automatically lock.

Refurbished Steris Reliance Synergy Sterilizer

Soma Tech Intl offers Steris Reliance Synergy Sterilizers up to 50% below OEM prices with the same service and warranty as new. The Steris Reliance Synergy is not only technically refurbished but also cosmetically refurbished to make it work and look like new. When the refurbishing process starts on the Steris Reliance Synergy, it is carefully inspected and tested by our own in-house biomedical engineers that are highly skilled and certified to work on sterilizers. If necessary, parts are replaced to make sure that all aspects of the Steris Reliance Synergy is functioning properly. Once everything is in working order, the unit is calibrated back to the original engineering manufacturer specifications. This ensures that the unit is working the same way that it originally left the manufacturer. After the Steris Reliance Synergy is working like new it undergoes a special cosmetic restoration process. The Steris Reliance Synergy is cleaned, minor scratches and dents are repaired, it's painted, and new decals are replaced if necessary. After this strenuous refurbishing process, the unit functions and looks like new. Soma Tech Intl is ISO 13485 certified and ensures that the best quality is given to all capital medical equipment that they sell. Before the Steris Reliance Synergy is labeled patient-ready and packed up for shipment, it goes through one last quality control test that makes sure all aspects are again working as they should. If you are looking to buy refurbished Steris Reliance Synergy sterilizers contact soma at [email protected] or call us at 1-800-GET-SOMA.

Soma Tech Intl is also actively looking to purchase a Steris Reliance Synergy If you or your facility is looking to sell your Steris Reliance Synergy, be sure to contact Soma Tech Intl. Soma has a dedicated and experienced purchasing department that helps you through the entire process. Selling your used or pre-owned Steris Reliance Synergy to Soma Tech Intl takes out the middle man in the equation. This also ensures that your medical facility gets top dollar for your equipment. Soma is 100% HIPPA compliant and makes sure that your equipment gets to our facility in the same condition that it left yours. Soma Tech Intl also gives the option for trade-in credit on your medical equipment. If you or your facility is looking to regain space for new equipment, or if you are looking to upgrade your current equipment, contact Soma Techn Intl's purchasing department at [email protected] or send us a message on our Sell to Soma website.

Questions about our Sterilizers?

Soma Tech Intl offers a wide range of sterilizers . If you have any questions about any of our sterilizers or need a quick quote, call 1-800-GET-SOMA and one of our knowledgeable sales representatives will help you.